Hydromaster & Hydrovac Kits

Repair kits for Hydromaster and Hydrovac vacuum boosters. 7 ManuMark hydromaster & hydrovac kits are listed below, including MM2709, MM33108, MM33108/1. Makes covered include Bendix, Clayton.

Hydromaster & Hydrovac Kits components manufactured by Pitchline Engineering for ManuMark

Hydromaster & Hydrovac Kits

Hydromaster and Hydrovac units boost braking with engine vacuum. The kits supply the diaphragms, cups and seals in the correct compounds for vacuum and brake fluid duty on these older but still widely used boosters.

Makes covered in this section

Bendix, Clayton

  • 7 listed kits and components in this category
  • Rubber parts moulded in-house in nitrile, EPDM, Viton or silicone to suit the fluid
  • Pistons, shafts and adaptors machined on our own CNC lathes and mills
  • Held in stock for ManuMark under JIT flexible manufacturing

Hydromaster & Hydrovac Kits part list

Quote the ManuMark (MM) part number when you enquire. The catalogue carries the original valve numbers and alternate part numbers for each line.

Part no.ProductReferencesCatalogue page
MM2709Air Seal (MM33108 & MM33122)Outside Diameter = 244 Inside Diameter = 188 Height = 18 1 Per KIT82
MM33108HYDROVAC #9320-1374Main Shaft 8mm 10mm For Air Seal see MM2709 Includes O-Rings & Seals82
MM33108/1HYDROVAC (Extra Long)—82
MM33109HYDROVAC #9320-1379Main Shaft 8mm Seal Outside Diameter = 175 Inside Diameter = 119 Height = 1882
MM33109/1JIDOSHAKIKIOutside Diameter = 175 Inside Diameter = 119 Height = 1883
MM33122BENDIXKIT No. 9320-1206 Main Shaft 8mm For Air Seal see MM2709 Includes O-Rings & Seals83
MM33143CLAYTON DEWANDREKIT No. 700 749 701 653 701 662/3 Main Shaft 8mm 701 290 701 659 Original has leather main seal 070 829 970 1662 Small U-Seal83

Other air brake repair kit categories

Air Dryer Repair Kits

Air dryer kits, adaptors and pistons for WABCO, KNORR and BOSCH air dryers.

Airmaster Repair Kits

Airmaster and air-over-hydraulic booster kits, pistons and shafts.

Brake Servo & Air Pack Kits

Repair kits for brake servos and air pack assemblies.

Calliper Repair Kits

Calliper seal and boot kits for air disc brakes across the major makes.

Calliper Pistons

Machined replacement calliper pistons for air disc brakes.

Circuit Protection Valve Kits

Four-circuit and multi-circuit protection valve repair kits.

Clutch Servo Repair Kits

The largest section in the range: clutch servo kits, pistons, master cylinders and shafts.

Compressor Repair Kits

Compressor gasket, valve plate and unloader components.

Foot Valve Repair Kits

Foot brake valve repair kits for single, dual and multi-circuit pedal valves.

Foot Valve Pistons

Replacement pistons and plungers for foot brake valves.

Governor Valve Kits

Governor valve repair kits controlling compressor cut-in and cut-out.

Hand Control Valve Kits

Hand brake and trailer hand control valve repair kits.

Load Sensing Valve Kits

Load sensing and load apportioning valve repair kits.

Solenoid & Miscellaneous Kits

Solenoid valve kits and the smaller items that sit outside the main groups.

Pressure Converter Kits

Air-to-hydraulic pressure converter repair kits.

Quick Release Valve Kits

Quick release valve repair kits for faster brake release.

Relay Valve & Modulator Kits

Relay control valve and ABS modulator repair kits.

Slack Adjuster Kits

Automatic and manual slack adjuster repair components.

Cast Iron Sleeves

Cast iron replacement sleeves in a range of bore sizes and lengths.

Splitter Valve Kits

Gearbox splitter and range change valve repair kits.

Spring Brake & Actuator Kits

One of the biggest sections: spring brake, booster and actuator kits, shafts and caps.

Trailer Control Valve Kits

Trailer control and emergency valve kits, with and without dump.

Unloader Valve Kits

Unloader valve repair kits for compressor and air dryer unloaders.

Hydromaster & Hydrovac Kits questions

How many hydromaster & hydrovac kits are in the ManuMark range?

There are 7 listed items in this category, part of the current ManuMark air brake range. The full list with part numbers is on this page and in the downloadable catalogue.

Which makes do your hydromaster & hydrovac kits cover?

This category covers Bendix, Clayton units among others. The catalogue cross-references original valve numbers and alternate part numbers so you can match an unbranded valve.

What is in a hydromaster & hydrovac kit?

Kits contain the moulded rubber seals, diaphragms and O-rings for the unit, together with the machined or pressed hard parts listed against that part number in the catalogue. Some pistons and shafts are supplied separately, which the catalogue notes against each line.

Which rubber compound is used?

The compound is matched to the fluid: nitrile for air, EPDM for brake fluid, Viton for mineral oil and silicone for heat applications. All rubber components are moulded in our own rubber department in Pinetown.

Are they made in South Africa?

Yes. The machined and moulded components are produced at our own factory at 32 Henwood Road, Pinetown, KwaZulu-Natal, and marketed under the ManuMark brand.

How do I order the right part?

Send us the ManuMark part number from the list on this page (for example MM2709 or MM33108), or the number stamped on the valve, and we will confirm the correct hydromaster & hydrovac kit before you order.

Who should fit these kits?

Air brake repair kits should only be fitted by qualified technicians with the necessary skill and expertise to ensure the kit's proper and safe operation. ManuMark kits are manufactured for use with unmodified OEM valves only.

South Africa

Hydromaster & Hydrovac Kits supplied across South Africa

Manufactured at our own factory at 32 Henwood Road, Pinetown, KwaZulu-Natal. Choose your province to explore the cities and industrial areas we cover.